Hydrophobic composite resins using a novel allylic urethane monomer as additive
DOI:
https://doi.org/10.29356/jmcs.v63i4.877Keywords:
Allylic monomer, dental additive, dental composite, resins, photopolymerizationAbstract
The purpose of this study is to report the formulation of photopolymerizable composites resins with hydrophobic behavior using a new urethane monomer (ETODC) as additive. The ETODC monomer was used together with Bis-GMA and TEGDMA to formulate a new organic matrix system. Mechanical and hydrophobic behavior were studied, also volumetric shrinkage, viscosity, polymerization kinetics and cytotoxicity were analyzed. Results were compared with a control resin prepared with Bis-GMA and TEGDMA. The results show that mechanical properties and volumetric shrinkage did not present statistical differences between the studied groups. When compared with the control material, the experimental resin formulated with the ETODC monomer showed higher hydrophobic behavior and higher values of degree of conversion and polymerization rate.
Downloads
References
Yin, M.; Liu, F.; He, J. J. Mech. Behav. Biomed. Mater. 2016, 57, 157-163. DOI: https://doi.org/10.1016/j.jmbbm.2015.11.020
Reinelt, S.; Tabatabai, M.; Moszner, N.; Fischer, U.K.; Utterodt, A.; Ritter, H. Macromol. Chem. Phys. 2014, 215, 1415-25. DOI: https://doi.org/10.1002/macp.201400174
Ferracane, J.L. Dent. Mater. 2011, 27, 29-38. DOI: https://doi.org/10.1016/j.dental.2010.10.020
Chen, M-H. J. Dent. Res. 2010, 89, 549-560. DOI: https://doi.org/10.1177/0022034510363765
Moszner, N.; Hirt, T. J. Polym. Sci., Part A-1: Polym. Chem. 2012, 50, 4369-4402. DOI: https://doi.org/10.1002/pola.26260
Peutzfeldt, A. Eur. J. Oral Sci. 1997, 105, 97-116. DOI: https://doi.org/10.1111/j.1600-0722.1997.tb00188.x
Martim, G.C.; Pfeifer, C.S.; Girotto, E.M. Mater. Sci. Eng., C. 2017, 72, 192-201. DOI: https://doi.org/10.1016/j.msec.2016.11.050
Martim, G.C.; Detomini, T.R.; Schuquel, I.T.; Radovanovic, E.; Pfeifer, C.S.; Girotto, E.M. Dent. Mater. 2014, 30, 155-163. DOI: https://doi.org/10.1016/j.dental.2013.11.002
Khatri, C.A.; Stansbury, J.W.; Schultheisz, C.R.; Antonucci, J.M. Dent. Mater. 2003; 19: 584-588. DOI: https://doi.org/10.1016/S0109-5641(02)00108-2
Stansbury, J.W. Dent. Mater. 2012, 28, 13-22. DOI: https://doi.org/10.1016/j.dental.2011.09.005
Pereira, S.G.; Nunes, T.G.; Kalachandra, S. Biomaterials. 2002, 23, 3799-3806. DOI: https://doi.org/10.1016/S0142-9612(02)00094-7
Ortiz, R.A.; Medina, L.A.R.; Duarte, M.L.B. J. Mater. Sci.: Mater. Med. 2013, 24, 2077-2084. DOI: https://doi.org/10.1007/s10856-013-4959-5
Eick, J.D.; Kotha, S.P.; Chappelow, C.C. Dent. Mater. 2007, 23, 1011-1017. DOI: https://doi.org/10.1016/j.dental.2006.09.002
Moszner, N.; Gianasmidis, A.; Klapdohr, S.; Fischer, U.K.; Rheinberger, V. Dent. Mater. 2008, 24, 851-856. DOI: https://doi.org/10.1016/j.dental.2007.10.004
Schneider, L.F.J.; Cavalcante, L.M.; Silikas, N.; Watts, D.C. J. Oral Sci. 2011, 53, 413-419. DOI: https://doi.org/10.2334/josnusd.53.413
Cruz-Aguilar, A.; Herrera-González, A.; Vázquez-García, R.; Navarro-Rodríguez, D.; Coreño, J. IOP Conference Series: Materials Science and Engineering. 2013, p. 012007. DOI: https://doi.org/10.1088/1757-899X/45/1/012007
González?López, J.A., Cuevas?Suárez, C.E.; Pérez?Mondragón, A.A.; Berlanga, Duarte. M.L.; Herrera?González. J. Appl. Polym. Sci. 2018, 135, 46240. DOI: https://doi.org/10.1002/app.46240
Herrera-González, A.M.; González-López, J.A; Cuevas-Suárez, C.E.; García-Castro, M.A.; Vargas-Ramírez, M. Polym. Compos. 2018, 39, E342-E350. DOI: https://doi.org/10.1002/pc.24453
Herrera?González ,M.A.; Cuevas?Suárez, C.E.; Caldera?Villalobos, M.; Pérez?Mondragón, A.A. J. Appl. Polym. Sci. 2016, 133, 4.
Pérez-Mondragón, A.A.; Cuevas-Suárez, C.E.; Castillo, O.R.S.; González-López, J.A.; Herrera-González, A.M. Mater. Sci. Eng. C. 2018, 93, 80-87. DOI: https://doi.org/10.1016/j.msec.2018.07.059
Cuevas-Suárez, C.E.; González-López, J.A.; da Silva, A.F.; Piva, E.; Herrera-González, A.M. J. Mech. Behav. Biomed. Mater. 2018, 87, 148-154. DOI: https://doi.org/10.1016/j.jmbbm.2018.07.016
Prakki, A.; Tallury, P.; Mondelli, R.F.L.; Kalachandra, S. Dent. Mat. 2007, 23, 1199-1204. DOI: https://doi.org/10.1016/j.dental.2006.10.007
Fujisawa, S.; Atsumi, T.; Satoh, K. In Vitro Mol. Toxicol. 2000, 13, 269-280.
Denis, A.B.; Plepis, A.M.G.; Martins, Vd.C.A., Pereira, J.C.; Cilli, R., Prakki, A. Mater. Res. 2012, 15, 397-402. DOI: https://doi.org/10.1590/S1516-14392012005000039
Dental ANSIA and Association. ANSI/ADA Specification No. 27:1993 Resin-Based Filling Materials. 1993.
ISO E. 4049 Dentistry-Polymer-based filling, restorative and luting materials. International Organization for Standardization, Geneva, Switzerland. 1988.
British Standard B and ISO E. 17304: 2013. Dentistry–polymerization shrinkage: method for determination of polymerization shrinkage of polymer-based restorative materials Brussels, Belgium: International Standards Organisation. 2013.
Sideridou, I.; Tserki, V.; Papanastasiou, G. Biomaterials. 2002, 23, 1819-1829. DOI: https://doi.org/10.1016/S0142-9612(01)00308-8
29. Neumann, M.G.; Miranda, Jr.W.G.; Schmitt, C.C.; Rueggeberg, F.A.; Correa, I.C. J. Dent.. 2005, 33, 525-532. DOI: https://doi.org/10.1016/j.jdent.2004.11.013
Cornelio, R.B.; Wikant, A.; Mjøsund, H. Acta Odontol. Scand. 2014, 72, 440-447. DOI: https://doi.org/10.3109/00016357.2013.856467
Moszner, N.; Salz, U. Progress in polymer science. 2001, 26, 535-576. DOI: https://doi.org/10.1016/S0079-6700(01)00005-3
Gonçalves, F.; Azevedo, C.L.; Ferracane, J.L.; Braga, R.R. Dent. Mater. 2011, 27, 520-526. DOI: https://doi.org/10.1016/j.dental.2011.01.007
Downloads
Additional Files
Published
Issue
Section
License
Authors who publish with this journal agree to the following terms:
- Authors retain copyright and grant the journal right of first publication with the work simultaneously licensed under a Creative Commons Attribution License that allows others to share the work with an acknowledgement of the work's authorship and initial publication in this journal.
- Authors are able to enter into separate, additional contractual arrangements for the non-exclusive distribution of the journal's published version of the work (e.g., post it to an institutional repository or publish it in a book), with an acknowledgement of its initial publication in this journal.
